Yamaha XVS65A Owner'S Manual Download

Page: 31 / 98

INSTRUMENT AND CONTROL FUNCTIONS

4-14

this system regularly and have a
Yamaha dealer repair it if it does not
function properly.

EAU15314

Ignition circuit cut-off system

The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.

●

It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.

●

It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.

●

It cuts the running engine when the
transmission is in gear and the
sidestand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

TIP

This check is most reliable if performed
with a warmed-up engine.

U1BF11E0.book Page 14 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands