Yamaha XVS65A Owner'S Manual Download

Page: 28 / 98

INSTRUMENT AND CONTROL FUNCTIONS

4-11

2. Install the passenger seat holder

by installing its bolts.

3. Install the passenger seat.

TIP

Make sure that the seats are properly
secured before riding.

EAU14282

Helmet holder

To open the helmet holder, insert the
key into the lock, and then turn the key
as shown.
To lock the helmet holder, place it in the
original position, and then remove the
key.

WARNING! Never ride with a

helmet attached to the helmet hold-
er, since the helmet may hit objects,
causing loss of control and possibly
an accident.

[EWA10161]

EAU14481

Storage compartment

The storage compartment is located on
the left side of the vehicle.

To open the storage compartment

1. Slide the lock cover open, insert

the key into the lock, and then turn
it clockwise.

2. Pull the storage compartment cov-

er out as shown.

1. Helmet holder

2. Unlock.

1. Storage compartment cover

2. Storage compartment lock cover

3. Storage compartment lock

U1BF11E0.book Page 11 Tuesday, April 13, 2010 9:28 AM

Summary of Contents for XVS65A



































































































Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands

Yamaha XVS65A, Owner'S Manual

Search results

Summary of Contents for XVS65A

Reviews:

Related manuals for XVS65A

Brands by name

Popular brands