background image

3-26

CHK

ADJ

CAUTION:

After adjusting the brake lever free play,
make sure there is no brake drag.

왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖 왖

ADJUSTING THE REAR BRAKE/

CHECKING THE BRAKE FLUID LEVEL

���

ZAUM0060

A

EAS00116

CHECKING THE BRAKE FLUID LEVEL
1. Stand the scooter on a level surface.

NOTE:
• Place the scooter on a suitable stand.
• Make sure the scooter is upright.

2. Check:

• brake fluid level

Below the minimum level mark 

 

 Add the

recommended brake fluid to the proper level.

Recommended brake fluid

DOT#3 or DOT#4

 A  Front brake

WARNING 

• Use only the designated brake fluid. Other

brake fluids may cause the rubber seals to
deteriorate, causing leakage and poor
brake performance.

• Refill with the same type of brake fluid that

is already in the system. Mixing brake fluids
may result in a harmful chemical reaction,
leading to poor brake performance.

• When refilling, be careful that water does

not enter the reser voir. Water will
significantly lower the boiling point of the
brake fluid and could cause vapor lock.

CAUTION:

Brake fluid may damage painted surfaces
and plastic parts. Therefore, always clean up
any spilt brake fluid immediately.

NOTE:
In order to ensure a correct reading of the brake
fluid level, make sure the top of the reservoir is
horizontal.

Summary of Contents for XN125 2000




































































































































































































































































Reviews: