Yamaha WOLVERINE YFM35XW Owner'S Manual Download

Page: 93 / 146

8-12

NOTE:

The engine oil should be between the minimum
and maximum level marks.

6. If the engine oil is at or below the minimum

level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.

7. Insert the dipstick into the oil filler hole, and

then tighten the engine oil filler cap.

To change the engine oil (with or without oil fil-
ter cartridge replacement)

1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Place an oil pan under the engine to collect

the used oil.

4. Remove the engine oil filler cap, and then re-

move the engine oil drain bolt to drain the oil
from the crankcase.

NOTE:

Skip steps 5–7 if the oil filter cartridge is not being
replaced.

1. Dipstick
2. Maximum level mark

3. Minimum level mark

1. Engine oil drain bolt

U3D510E0.book Page 12 Friday, December 2, 2005 1:07 PM

Summary of Contents for WOLVERINE YFM35XW



















































































































































Search results

Summary of Contents for WOLVERINE YFM35XW

Reviews:

Related manuals for WOLVERINE YFM35XW

Brands by name

Popular brands

Yamaha WOLVERINE YFM35XW, Owner'S Manual

Search results

Summary of Contents for WOLVERINE YFM35XW

Reviews:

Related manuals for WOLVERINE YFM35XW

Brands by name

Popular brands