Yamaha WOLVERINE YFM35XW Owner'S Manual Download | Manualshive

Page: 105 / 146

background image

8-24

8

crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

NOTE:

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24041

Adjusting the throttle cable free play

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) as shown. Periodically
check the throttle cable free play and, if necessary,
adjust it as follows.

NOTE:

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Loosen the locknut.
2. To increase the throttle cable free play, turn

the adjusting bolt in direction (a). To decrease
the throttle cable free play, turn the adjusting
bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U3D510E0.book Page 24 Friday, December 2, 2005 1:07 PM

«
...
103
104
105
106
107
...
»

Summary of Contents for WOLVERINE YFM35XW



















































































































































Reviews:

No comments

Related manuals for WOLVERINE YFM35XW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands