Yamaha WOLVERINE YFM35XW Owner'S Manual Download | Manualshive

Page: 32 / 146

background image

4-14

4

●

Do not exceed the maximum load of 100.0 kg
(220 lb) for the ATV.

NOTE:

Drain plugs are fitted at the bottom of the storage
compartment. If any water collects in the storage
compartment, remove the drain plugs, drain the
water, and then install the drain plugs.

EBU18980

Adjusting the front shock absorber
assemblies

The spring preload can be adjusted to suit the rid-
er’s weight and the riding conditions.
Adjust the spring preload as follows.

Turn the adjusting ring in direction (a) to increase
the spring preload and thereby harden the suspen-
sion, and in direction (b) to decrease the spring
preload and thereby soften the suspension.

NOTE:

A special wrench can be obtained at a Yamaha
dealer to make this adjustment.

1. Storage compartment drain plug

1. Spring preload adjusting ring
2. Position indicator

U3D510E0.book Page 14 Friday, December 2, 2005 1:07 PM

«
...
30
31
32
33
34
...
»

Summary of Contents for WOLVERINE YFM35XW



















































































































































Reviews:

No comments

Related manuals for WOLVERINE YFM35XW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands