Yamaha WOLVERINE YFM35XW Page 122 Owner'S Manual Download

Page: 122 / 146

8-41

3. Insert a new bulb into the socket, push it in,

and then turn it clockwise until it stops.

4. Install the lens by installing the screws.

CAUTION:

ECB00700

Do not overtighten the screws, otherwise the
lens may break.

EBU25650

Removing a wheel

1. Loosen the wheel nuts.

2. Elevate the ATV and place a suitable stand

under the frame.

3. Remove the nuts from the wheel.

4. Remove the wheel.

EBU25700

Installing a wheel

1. Install the wheel and the nuts.

NOTE:

●

The arrow mark

on the tire must point toward

the rotating direction of the wheel.

●

Tapered nuts are used for both the front and rear
wheels. Install the nuts with their tapered side to-
wards the wheel.

1. Nut

1. Arrow mark

U3D510E0.book Page 41 Friday, December 2, 2005 1:07 PM

Summary of Contents for WOLVERINE YFM35XW



















































































































































Search results

Summary of Contents for WOLVERINE YFM35XW

Reviews:

Related manuals for WOLVERINE YFM35XW

Brands by name

Popular brands

Yamaha WOLVERINE YFM35XW, Owner'S Manual

Search results

Summary of Contents for WOLVERINE YFM35XW

Reviews:

Related manuals for WOLVERINE YFM35XW

Brands by name

Popular brands