Yamaha WOLVERINE YFM35XW Owner'S Manual Download | Manualshive

Page: 116 / 146

background image

8-35

8

WARNING

EWB02140

To charge the battery

Have a Yamaha dealer charge the battery as soon
as possible if it seems to have discharged. Keep in
mind that the battery tends to discharge more
quickly if the ATV is equipped with optional electri-
cal accessories.

To store the battery

1. If the ATV will not be used for more than one

month, remove the battery, fully charge it, and
then place it in a cool, dry place.

2. If the battery will be stored for more than two

months, check it at least once a month and ful-
ly charge it if necessary.

To install the battery

NOTE:

Be sure the battery is fully charged.

1. Install the battery.
2. Make sure to properly connect the battery

leads to the battery terminals.

POTENTIAL HAZARD
Failure to handle batteries or battery electro-
lyte carefully.
WHAT CAN HAPPEN
You could be poisoned. You could be se-
verely burned by the sulfuric acid in battery
electrolyte. Batteries produce explosive gas-
es.
HOW TO AVOID THE HAZARD
Avoid contact with skin, eyes or clothing. Al-
ways shield eyes when working near batter-
ies. Keep out of reach of children.
Antidote:
EXTERNAL: Flush with water.
INTERNAL: Drink large quantities of water or
milk. Follow with milk of magnesia, beaten
egg or vegetable oil. Get prompt medical at-
tention.
EYES: Flush with water for 15 minutes and
get prompt medical attention. Keep batteries
away from sparks, flames, cigarettes or oth-
er sources of ignition. Ventilate when charg-
ing or using in a closed space.

U3D510E0.book Page 35 Friday, December 2, 2005 1:07 PM

«
...
114
115
116
117
118
...
»

Summary of Contents for WOLVERINE YFM35XW



















































































































































Reviews:

No comments

Related manuals for WOLVERINE YFM35XW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands