Yamaha WOLVERINE YFM35XW Page 71 Owner'S Manual Download | Manualshive

Page: 71 / 146

background image

7-21

7

If your ATV has stalled or stopped and you believe
you can continue up the hill, restart carefully to
make sure you do not lift the front wheels which
could cause you to lose control. If you are unable
to continue up the hill, dismount the ATV on the up-
hill side. Physically turn the ATV around and then
descend the hill.
If you start to roll backwards, DO NOT apply the
rear brake to stop or try to put the ATV in gear. The
ATV could easily tip over backwards. Instead, ap-
ply the front brake gradually, or dismount the ATV
immediately on the uphill side.

WARNING

EWB01261

POTENTIAL HAZARD
Stalling, rolling backwards or improperly dis-
mounting while climbing a hill.
WHAT CAN HAPPEN
Could result in ATV overturning.
HOW TO AVOID THE HAZARD
Maintain a steady speed when climbing a
hill.

If you lose all forward speed:

●

Keep weight uphill.

●

Apply the brakes.

●

Apply the parking brake after you are
stopped.

If you begin rolling backwards:

●

Keep weight uphill.

●

Never apply the rear brake while rolling
backwards. Apply the front brake.

●

When fully stopped, apply the rear brake
as well, and then lock the parking brake.

Dismount on uphill side or to a side if point-
ed straight uphill. Turn the ATV around and
remount, following the procedure described
in the Owner’s Manual.

U3D510E0.book Page 21 Friday, December 2, 2005 1:07 PM

«
...
69
70
71
72
73
...
»

Summary of Contents for WOLVERINE YFM35XW



















































































































































Reviews:

No comments

Related manuals for WOLVERINE YFM35XW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands