Yamaha WOLVERINE YFM35XW Owner'S Manual Download | Manualshive

Page: 57 / 146

background image

7-7

7

WARNING

EWB00950

WARNING

EWB00010

Indicates a potential hazard that could result in
serious injury or death.

Do not operate at speeds too fast for your skills
or the conditions.

WARNING

EWB00960

POTENTIAL HAZARD
Operating this ATV with improper tires, or
with improper or uneven tire pressure.
WHAT CAN HAPPEN
Use of improper tires on this ATV, or opera-
tion of this ATV with improper or uneven tire
pressure, may cause loss of control, in-
creasing your risk of an accident.
HOW TO AVOID THE HAZARD
Always use the size and type tires specified
in the Owner’s Manual for this ATV on page
5-6.
Always maintain proper tire pressure as de-
scribed in the Owner’s Manual on page 5-7.

POTENTIAL HAZARD
Operating this ATV at speeds too fast for
your skills or the conditions.
WHAT CAN HAPPEN
Increases your chances of losing control of
the ATV, which can result in an accident.
HOW TO AVOID THE HAZARD
Always go at a speed that is proper for the
terrain, visibility and operating conditions,
and your experience.

U3D510E0.book Page 7 Friday, December 2, 2005 1:07 PM

«
...
55
56
57
58
59
...
»

Summary of Contents for WOLVERINE YFM35XW



















































































































































Reviews:

No comments

Related manuals for WOLVERINE YFM35XW

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands