Yamaha VF200 Page 75 Owner'S Manual Download

Page: 75 / 120

Operation

Tilting down when using the tilt support lever
1. Push the “

” (up) side of the power trim

and tilt switch until the outboard motor is
supported by the tilt rod and the tilt sup-
port lever becomes free.

2. Release the tilt support lever.

3. Push the “

” (down) side of the power

trim and tilt switch to tilt the outboard
motor down.

EMU28063

Shallow water

EMU40702

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

NOTICE

ECM02361

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

1. Power trim and tilt switch

ZMU06941

ZMU069

ZMU07178

1. Power trim and tilt switch

ZMU06941

ZMU069

6CB-9-3B-1E0.book 69 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for VF200

























































































































Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands

Yamaha VF200, Owner'S Manual

Search results

Summary of Contents for VF200

Reviews:

Related manuals for VF200

Brands by name

Popular brands