Yamaha VF200 Owner'S Manual Download Page 61

Page: 61 / 120

Operation

2. Check that the rubber seal is seated all

the way around the bottom cowling.

3. Check that all of the cowling lock levers

are pulled outward.

4. Align the 3 protrusions on the top cowl-

ing with the corresponding holders on
the bottom cowling, and then place the
top cowling on the bottom cowling.

5. Push the cowling lock levers inward to

secure the top cowling.

6. Check the fitting of the top cowling by

pushing it with both hands.

NOTICE:

the top cowling is not installed cor-
rectly, water can enter the top cowl-
ing and damage the engine, or the top
cowling can blow off at high speeds.

[ECM02371]

1. Top cowling
2. Protrusion
3. Holder
4. Bottom cowling

ZMU07015

ZMU07016

1. Cowling lock lever

1. Cowling lock lever(s)

ZMU06920

ZMU06921

ZMU06922

6CB-9-3B-1E0.book 55 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for VF200

























































































































Search results

Summary of Contents for VF200

Reviews:

Yamaha VF200, Owner'S Manual, Page: 61 / 120

Search results

Summary of Contents for VF200

Reviews: