Yamaha VF200 Page 21 Owner'S Manual Download | Manualshive

Page: 21 / 120

background image

Specifications and requirements

15

Trim and tilt system:

Power trim and tilt

Propeller mark:

M/T (VF250XA)
T (VF200A, VF225A, VF250LA)

Fuel and oil:

Recommended fuel:

Mid-grade unleaded gasoline (For
North America), Premium unleaded
gasoline (VF225A, VF250A)
Regular unleaded gasoline (VF200A)

Min. pump octane number (PON):

86 (VF200A)
89 (VF225A, VF250A)

Min. research octane number (RON):

90 (VF200A)
94 (VF225A, VF250A)

Recommended engine oil:

YAMALUBE 4M FC-W or 4-stroke
outboard motor oil

Recommended engine oil grade 1:

SAE 5W-30/10W-30
API SE/SF/SG/SH/SJ/SL

Engine oil quantity (without oil filter re-
placement):

6.4 L (6.76 US qt, 5.63 Imp.qt)

Engine oil quantity (with oil filter replace-
ment):

6.7 L (7.08 US qt, 5.90 Imp.qt)

Lubrication system:

Wet sump

Recommended gear oil:

Yamalube Marine Gearcase Lube HD
or Hypoid gear oil

Recommended gear oil grade:

SAE 90 API GL-4 / SAE 80W API
GL-5 / SAE 90 API GL-5

Gear oil quantity:

1.040 L (1.099 US qt, 0.915 Imp.qt)

Tightening torque:

Spark plug:

28 N·m (2.86 kgf·m, 20.7 lb·ft)

Propeller nut:

54 N·m (5.51 kgf·m, 39.8 lb·ft)

Engine oil drain bolt:

27 N·m (2.75 kgf·m, 19.9 lb·ft)

Engine oil filter:

18 N·m (1.84 kgf·m, 13.3 lb·ft)

EMU33556

Installation requirements

EMU33565

Boat horsepower rating

WARNING

EWM01561

Overpowering a boat can cause severe
instability.

Before installing the outboard motor(s), con-
firm that the total horsepower of your out-
board motor(s) does not exceed the boats
maximum horsepower rating. See the boat’s
capacity plate or contact the manufacturer.

EMU40491

Mounting outboard motor

WARNING

EWM02501



Improper mounting of the outboard mo-
tor could result in hazardous condi-
tions such as poor handling, loss of
control, or fire hazards.



Because the outboard motor is very
heavy, special equipment and training
is required to mount it safely.

Your dealer or other person experienced in
proper rigging should mount the outboard
motor using correct equipment and complete
rigging instructions. For further information,
see page 49.

6CB-9-3B-1E0.book 15 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
19
20
21
22
23
...
»

Summary of Contents for VF200

























































































































Reviews:

No comments

Related manuals for VF200

DCDC SBC Series

Brand: Infineon Pages: 17

Brand: JETWAY Pages: 46

Brand: Supero Pages: 105

Brand: Beck Pages: 24

STM32 Nucleo-32

Brand: ST Pages: 37

SKR E3 DIP V1.0

Brand: BIGTREETECH Pages: 10

B560M DS3H PLUS

Brand: Gigabyte Pages: 42

Brand: Gigabyte Pages: 96

Brand: Biostar Pages: 118

Brand: IEI Technology Pages: 198

Fatal1ty B150 Gaming K4

Brand: ASROCK Pages: 154

Brand: TYAN Pages: 118

Brand: Gigabyte Pages: 46

Brand: JETWAY Pages: 53

Brand: JETWAY Pages: 48

Brand: ST Pages: 14

Brand: Gigabyte Pages: 120

Brand: Freescale Semiconductor Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands