Yamaha VF200 Owner'S Manual Download | Manualshive

Page: 43 / 120

background image

Instruments and indicators

37

NOTICE

ECM02302



Do not continue to operate the engine if
the low oil pressure-alert indicator is on
and the engine oil pressure is low. Seri-
ous engine damage will occur.



The low oil pressure-alert indicator
does not indicate the engine oil level.
Use the oil dipstick to check the oil lev-
el. For further information, see page 53.

EMU26584

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
46.

NOTICE

ECM00053

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26603

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36062

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

1. Low oil pressure-alert indicator

ZMU01736

1

1. Overheat-alert indicator

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Alert indicator(s)

ZMU01737

1

TRIP

TIME

BATT

km/h

knot

mph

km

mile

SPEED

YAMAHA

set

mode

1

2

4

3

ZMU07000

6CB-9-3B-1E0.book 37 ページ２０１７年１１月１６日　木曜日　午後５時２９分

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
41
42
43
44
45
...
»

Summary of Contents for VF200

























































































































Reviews:

No comments

Related manuals for VF200

Brand: Digital Equipment Pages: 98

microComponents mp6-XEVA

Brand: Bartels Mikrotechnik Pages: 9

STEVAL-IME008V1

Brand: STMicroelectronics Pages: 19

AR0832MBSC25SUFAH-GEVB

Brand: ON Semiconductor Pages: 6

Brand: Unicorn Computer Pages: 36

Brand: XFX Pages: 120

P35D3 Platinum - Motherboard - ATX

Brand: MSI Pages: 104

Brand: CAME Pages: 8

Brand: DFI Pages: 73

Brand: 96Boards Pages: 22

Brand: Alinx Pages: 29

EVB-LAN9252-SPI

Brand: Microchip Technology Pages: 22

Brand: Watersnake Pages: 24

Brand: WinSystems Pages: 85

Brand: DediProg Pages: 23

Brand: ASROCK Rack Pages: 83

Brand: ASROCK Rack Pages: 83

Brand: Baumer Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands