Yamaha VF200 Owner'S Manual Download Page 116

Page: 116 / 120

INDEX

110

Hot parts ................................................. 1
Hour meter............................................ 36

Identification numbers record ................. 9
Impact damage ................................... 101
Installation requirements....................... 15

Key number ............................................ 9

Laws and regulations.............................. 4
Low battery voltage-alert indicator........ 39
Low oil pressure alert............................ 46
Low oil pressure-alert indicator............. 36
Lubrication ............................................ 73

Main switch ........................................... 31
Maintenance chart 1 ............................. 76
Maintenance chart 2 ............................. 78
Maintenance interval guidelines ........... 75
Modifications........................................... 2
Mounting height .................................... 49
Mounting outboard motor...................... 15
Mounting the outboard motor................ 49
Muddy or acidic water........................... 20

Neutral interlock trigger......................... 28

Operating engine .................................. 57
Outboard motor, checking .................... 54
Outboard motor disposal

requirements ...................................... 20

Outboard motor (painted surface),

checking ............................................. 74

Outboard motor safety ............................ 1
Outboard motor serial number................ 9
Overheat alert ....................................... 46
Overheat-alert indicator ........................ 37

Overloading ............................................ 2

Passengers............................................. 2
Passenger training.................................. 4
People in the water ................................. 2
Periodic maintenance ........................... 74
Personal flotation devices (PFDs) .......... 2
Power trim and tilt ................................... 1
Power trim and tilt switch (bottom

cowling) .............................................. 31

Power trim and tilt switch (remote

control)................................................ 31

Power trim and tilt unit, checking .......... 56
Power trim and tilt unit will not

operate ............................................. 102

Propeller ................................................. 1
Propeller, inspecting ............................. 90
Propeller, installing ............................... 91
Propeller, removing............................... 91
Propeller selection ................................ 17

Read manuals and labels ..................... 11
Remote control box............................... 27
Remote control lever............................. 28
Remote control requirements ............... 16
Replacement parts................................ 74
Rotating parts ......................................... 1
Rules when encountering vessels .......... 5

Sending fuel.......................................... 57
Shallow water ....................................... 69
Shifting.................................................. 61
Shifting (checks after engine warm

up) ...................................................... 60

Spark plug, inspecting .......................... 80
Specifications........................................ 14
Speedometer ........................................ 37
Star labels............................................. 21
Start-in-gear protection ......................... 17
Starting engine...................................... 58

6CB-9-3B-1E0.book 110 ページ２０１７年１１月１６日　木曜日　午後５時２９分

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for VF200

























































































































Search results

Summary of Contents for VF200

Reviews:

Yamaha VF200, Owner'S Manual, Page: 116 / 120

Search results

Summary of Contents for VF200

Reviews: