manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 72

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-36

 

1

2

3

4

5

6

7

8

9

 

EAU24360

 

Front wheel 

 

EAU24582

 

To remove the front wheel

WARNING

 

EWA10821

 

To avoid injury, securely support the
vehicle so there is no danger of it

 

falling over.

 

1. Disconnect the speedometer ca-

ble from the front wheel.

2. Loosen the axle nut.

3. Lift the front wheel off the ground

according to the procedure in
“Supporting the motorcycle” on

page 7-35.

4. Remove the axle nut, pull the

wheel axle out, and then remove
the wheel. 

 

NOTICE:

 

 Do not apply

the brake after the wheel has
been removed together with the
brake disc, otherwise the brake
pads will be forced shut.

 

[ECA11071]

 

 

 

EAU24981

 

To install the front wheel

 

1. Install the speedometer gear unit

into the wheel hub so that the pro-
jections mesh with the slots.

2. Lift the wheel up between the fork

legs.

TIP

 

Make sure that there is enough space
between the brake pads before insert-
ing the brake disc and that the slot in
the speedometer gear unit fits over the

 

retainer on the fork leg.

3. Insert the wheel axle, and then in-

stall the axle nut.

4. Lower the front wheel so that it is

on the ground.

5. Tighten the axle nut to the speci-

fied torque.

 

1. Speedometer cable

2. Axle nut

1

2

 

1. Speedometer gear unit

1

 

1. Speedometer gear unit retainer

2. Speedometer cable

 

Tightening torque:

 

Axle nut:

90 Nm (9.0 m·kgf, 65 ft·lbf)

2

1

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands