manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 56

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-20

 

1

2

3

4

5

6

7

8

9

 

in direction (b).

7. Tighten the locknut at the crank-

case.

8. Tighten the locknut at the clutch le-

ver and then slide the rubber cover
to its original position.

 

EAU22093

 

Adjusting the brake lever free 
play 

 

The brake lever free play should mea-
sure 5.0–8.0 mm (0.20–0.31 in) as
shown. Periodically check the brake le-
ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the brake le-

ver.

2. To increase the brake lever free

play, turn the brake lever free play
adjusting screw in direction (a). To
decrease the brake lever free play,
turn the adjusting screw in direc-

tion (b).

3. Tighten the locknut.

WARNING

 

EWA10630

 

●

 

After adjusting the brake lever
free play, check the free play
and make sure that the brake is
working properly.

 

●

 

A soft or spongy feeling in the
brake lever can indicate the
presence of air in the hydraulic
system. If there is air in the hy-
draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin-
ish the braking performance,
which may result in loss of con-

 

trol and an accident.

 

1. Locknut

2. Brake lever free play adjusting screw

3. Brake lever free play

1 2

3

(b)

(a)

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands