manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 22

 

INSTRUMENT AND CONTROL FUNCTIONS

 

4-4

 

1

2

3

4

5

6

7

8

9

 

EAU12820

 

Clutch lever 

 

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle-
bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni-
tion circuit cut-off system. (See
page 4-11.)

 

EAU12870

 

Shift pedal 

 

The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 5-speed con-
stant-mesh transmission equipped on
this motorcycle.

 

EAU12890

 

Brake lever 

 

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

 

1. Clutch lever

1

 

1. Shift pedal

1

N

5
4
3
2

1

 

1. Brake lever

1

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands