manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 66

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-30

 

1

2

3

4

5

6

7

8

9

 

EAU23363

 

Battery 

 

A poorly maintained battery will corrode
and discharge quickly. The electrolyte
level, battery lead connections and
breather hose routing should be
checked before each ride and at the in-
tervals specified in the periodic mainte-
nance and lubrication chart.

 

To check the electrolyte level

 

1. Remove the seat. (See page 4-8.)
2. Disconnect the negative battery

lead from the battery.

3. Disconnect the positive battery

lead and the battery breather hose
from the battery.

4. Unhook the battery band, and then

pull the battery out of the battery
compartment.

5. Place the battery on a level sur-

face, and then check the electro-
lyte level in the battery.

TIP

 

The electrolyte should be between the

 

minimum and maximum level marks.

6. If the electrolyte is at or below the

minimum level mark, add distilled
water to raise the electrolyte to the
maximum level mark. 

 

NOTICE:

 

Use only distilled water, as tap
water contains minerals that are
harmful to the battery.

 

[ECA10611]

 

 

WARNING

 

EWA10760

 

●

 

Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case

 

1. Battery

2. Negative battery lead (black)

3. Positive battery lead (red)

4. Battery breather hose

5. Battery band

4

1

2

3

5

 

1. Maximum level mark

2. Minimum level mark

1

2

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands