manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 63

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-27

 

2

3

4

5

6

7

8

9

 

EAU23182

 

Checking and lubricating the 
brake pedal 

 

The operation of the brake pedal
should be checked before each ride,
and the pedal pivot should be lubricat-
ed if necessary.

 

EAU23202

 

Checking and lubricating the 
sidestand 

 

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

 

EWA10731

 

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the sidestand could contact the
ground and distract the operator, re-

 

sulting in a possible loss of control.

 

Recommended lubricants:

 

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease

 

Recommended lubricant:

 

Lithium-soap-based grease

 

Recommended lubricant:

 

Lithium-soap-based grease

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands