manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 28

 

INSTRUMENT AND CONTROL FUNCTIONS

 

4-10

 

1

2

3

4

5

6

7

8

9

 

EAU15112

 

Carrier 

WARNING

 

EWA10171

 

●

 

Do not exceed the load limit of 3
kg (7 lb) for the carrier.

 

●

 

Do not exceed the maximum
load of 179 kg (395 lb) (CAL)
180 kg (397 lb) (U49) for the ve-

 

hicle.

 

EAU15170

 

Luggage strap holders 

 

There are four luggage strap holders
below the carrier.

 

EAU15303

 

Sidestand 

 

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

TIP

 

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See page 4-11 for an explanation of

 

the ignition circuit cut-off system.) 

WARNING

 

EWA10240

 

The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described
below and have a Yamaha dealer re-

 

1. Carrier

1

 

1. Luggage strap holder

1

1

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands