manualshive.com logo in svg

Yamaha TW200Z, Owner'S Manual

Share
Download
Yamaha TW200Z Owner'S Manual Download Page 50

 

PERIODIC MAINTENANCE AND ADJUSTMENT

 

7-14

 

1

2

3

4

5

6

7

8

9

 

EAU20822

 

Cleaning the air filter element 
and check hose 

 

The air filter element should be cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
Clean the air filter element more fre-
quently if you are riding in unusually
wet or dusty areas. In addition, the air
filter check hose must be frequently
checked and cleaned if necessary.

 

To clean the air filter element

 

1. Remove panel A. (See page 7-8.)
2. Remove the air filter case cover by

removing the screws.

3. Pull the air filter element out.
4. Remove the sponge material from

the air filter element frame, clean it
with solvent, and then squeeze the
remaining solvent out.

5. Apply oil of the recommended type

to the entire surface of the sponge
material, and then squeeze the ex-
cess oil out.

TIP

 

The sponge material should be wet but

 

not dripping.

6. Pull the sponge material over the

air filter element frame.

7. Insert the element into the air filter

case. 

 

NOTICE:

 

 Make sure that

the air filter element is properly
seated in the air filter case. The
engine should never be operat-
ed without the air filter element
installed, otherwise the pis-
ton(s) and/or cylinder(s) may
become excessively worn.

 

[ECA10481]

 

 

8. Install the air filter case cover by in-

stalling the screws.

9. Install the panel.

 

1. Air filter case cover

2. Screw

1

2

2

 

1. Sponge material

2. Air filter element frame

1

2

 

Recommended oil:

 

Yamaha foam air filter oil or other 
quality foam air filter oil

Summary of Contents for TW200Z



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands