Yamaha MX825V-EFI Service Manual Download Page 23 | Manualshive

Page: 23 / 59

background image

SERVICE TIP

Model :

MX825V-EFI

23

Oil Pressure Switch Operation

The Oil Pressure Switch completes the ground circuit
for the Oil Pressure Warning light:
1. when the engine is not running and the

Main Switch is turned to the ON or START
position, and

2. if the oil pressure drops during operation.

Condition

Engine running with

normal oil pressure

Engine not running

Oil pressure less than

7.1 psi (49 kPA)

Switch contacts

OPEN

CLOSED

CLOSED

Oil Pressure

warning light

OFF

ON

ON

«
...
21
22
23
24
25
...
»

Summary of Contents for MX825V-EFI




























































Reviews:

No comments

Related manuals for MX825V-EFI

Vickers M2-200 Series

Brand: Eaton Pages: 13

Brand: Amico Pages: 47

2-10-4 TEXAS STEAM ENGINE

Brand: Premier Pages: 24

Brand: Grizzly Pages: 2

Brand: Habasit Pages: 54

Brand: DLE Pages: 4

Brand: DLE Pages: 24

Brand: Fanotec Pages: 2

Brand: ST Pages: 251

Ultra Drive UN-99

Brand: Bettcher Pages: 29

Brand: LONCIN Pages: 23

Brand: LONCIN Pages: 26

Brand: Mitsubishi Heavy Industries Pages: 32

Brand: ZIEHL-ABEGG Pages: 88

Brand: Vetus Pages: 80

Brand: Danfoss Pages: 69

Brand: Kärcher Pages: 180

Brand: Lenze Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands