manualshive.com logo in svg

Yamaha MX825V-EFI, Service Manual

Share
Download
Yamaha MX825V-EFI Service Manual Download Page 46

15

Periodic maintenance

11.

Turn the engine off and wipe the engine oil dipstick
clean, insert it back into the oil filler hole (without
screwing it in), and then remove it again to check
the oil level.

TIP

The engine oil should be between the minimum and
maximum level marks.

12.

If the engine oil is below the minimum level mark,
add sufficient oil of the recommended type to raise
it to the correct level.

13.

Install and tighten the oil filler cap.

Air filter

1.

Unhook the holding clips, and then remove the air
filter case cover from the air filter case.

2.

Pull the air filter element out.

3.

Replace the air filter element and check condition
of inner element. If inner element is damaged or
dirty, replace it.

4.

Install new element(s) into the air filter case.

1. Minimum level mark
2. Maximum level mark
3. Engine oil dipstick
4. Oil filler cap

1. Air filter case cover
2. Holding clip
3. Air filter case

1

2

3

4

5

1. Dust cap
2. Air filter case cover
3. Air filter element
4. Inner element
5. Air filter case

Summary of Contents for MX825V-EFI




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands