Yamaha MX825V-EFI Service Manual Download Page 47 | Manualshive

Page: 47 / 59

background image

16

Periodic maintenance

5.

Install the air filter case cover.

6.

Place the holding clips in the original position.

7.

Remove the dust cap on the air filter case cover for
accumulated dirt or water.

8.

If dirt or water is visible, clean it, and then install it.

Spark arrester (For models equipped

with a muffler)

1.

Remove the screw.

The engine should never run without the air filter
element; excessive piston and cylinder wear may
result.

NOTICE

The engine and muffler will be very hot after the
engine has been run.
Avoid touching the engine and muffler while they
are still hot with any part of your body or clothing
during inspection or repair.

WARNING

1

1. Screw

«
...
45
46
47
48
49
...
»

Summary of Contents for MX825V-EFI




























































Reviews:

No comments

Related manuals for MX825V-EFI

Brand: Saito Pages: 2

TSA 200-100-220

Brand: SCHABMULLER Pages: 56

Brand: WPT POWER Pages: 39

Brand: Plettenberg Pages: 26

Brand: Tanaka Pages: 10

Brand: Oxygen Pages: 6

Brand: MTU Pages: 156

Brand: Sachs Pages: 42

Brand: Siemens Pages: 4

SIMOTICS A-1FV5

Brand: Siemens Pages: 66

Brand: Siemens Pages: 56

SIMODRIVE POSMO A

Brand: Siemens Pages: 58

Brand: Siemens Pages: 100

Simotics HV C 1NA14544WA600AG0-Z

Brand: Siemens Pages: 112

SIMOTICS DP 1PC13

Brand: Siemens Pages: 100

SIMOTICS DP 1PC134

Brand: Siemens Pages: 120

SIMOTICS HT Series

Brand: Siemens Pages: 128

Brand: Siemens Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands