manualshive.com logo in svg

Yamaha MX825V-EFI, Service Manual

Share
Download
Yamaha MX825V-EFI Service Manual Download Page 55

24

Exhaust emission control system and 

components

The above items and the corresponding acronyms are provided in accordance with U.S. 
EPA REGULATIONS FOR NEW NONROAD SPARK-IGNITION NONHANDHELD 
ENGINES and the CALIFORNIA REGULATIONS FOR 1995 AND LATER SMALL 
OFFROAD ENGINES.
The acronyms conform to the latest version of the SAE’s recommended practice docu-
ment J1930, “Diagnostic Acronyms, Terms, and Definitions For Electrical/Electronic 
System”.

It is recommended that these items be serviced by a Yamaha dealer.

Item

9

 Fuel Injection ........................................

9

Engine Control Unit ..............................

9

Throttle Position Sensor ......................

9

Crank Position Sensor .........................

9

Intake Manifold Air Pressure  ..............
Sensor & Intake Temp. Sensor

9

  O

2

 Sensor  ..............................................

9

Ignition Coil & Spark Plug  ...................

9

 Fuel Pump .............................................

9

 Crankcase .............................................

9

Air  Filter Assy.  .....................................

9

Engine Temp. Sensor 
(Muff & Spark Arrester)  Option

FI
ECU
TP Sensor
CKP (Crank shaft Position) 
Sensor
MAPT (Manifold Absolute 
Pressure and Temperature) 
Sensor
O

2

S

EI (Electronic Ignition)
FP
PCV (Positive Crankcase 
Ventilation)
ACL

Acronym

Summary of Contents for MX825V-EFI




























































Reviews:

No comments

Brands by name

Popular brands

Load more brands