Yamaha FZ8 Owner'S Manual Download

Page: 78 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-35

9. Install the headlight bulb cover,

then connect the headlight cou-
pler.

10. Connect the coupler, then insert

the projection on the headlight unit
into the grommet on the vehicle to
fit the headlight unit in its original
position.

11. Install the headlight unit bolts.
12. Install the bolt behind the headlight

unit.

13. Place the side covers in their origi-

nal position, then install their bolt.

14. Place the top cover in its original

position, and then install its bolts.

15. Have a Yamaha dealer adjust the

headlight beam if necessary.

EAU24115

Replacing the tail/brake light
bulb

1. Remove the passenger seat. (See

page 4-14.)

2. Remove the tail/brake light bulb

socket (together with the bulb) by
turning it counterclockwise.

3. Remove the burnt-out bulb by

pushing it in and turning it counter-
clockwise.

4. Insert a new bulb into the socket,

push it in, and then turn it clock-
wise until it stops.

5. Install the socket (together with the

bulb) by turning it clockwise.

6. Install the passenger seat.

1. Projection
2. Grommet

1. Tail/brake light bulb socket

U39P10E0.book Page 35 Thursday, October 7, 2010 5:12 PM

Summary of Contents for FZ8













































































































Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands

Yamaha FZ8, Owner'S Manual

Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands