Yamaha FZ8 Owner'S Manual Download | Manualshive

Page: 42 / 108

background image

OPERATION AND IMPORTANT RIDING POINTS

6-3

6

4. At the recommended shift points

shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second

gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)

6. Open the throttle part way and

gradually release the clutch lever.

7. Follow the same procedure when

shifting to the next higher gear.

TIP

When shifting gears in normal operat-
ing conditions, use the recommended
shift points.

EAU16700

To decelerate

1. Apply both the front and the rear

brakes to slow the motorcycle.

2. Shift the transmission into first

gear when the motorcycle reaches
25 km/h (16 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu-

tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

EAU16740

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17093

0–1000 km (0–600 mi)

Avoid prolonged operation above 5800
r/min.

NOTICE:

After 1000 km (600

mi) of operation, the engine oil must
be changed and the oil filter car-
tridge or element replaced.

[ECA10302]

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 6900
r/min.

Shift up points:

1st

→

2nd: 20 km/h (12 mi/h)

2nd

→

3rd: 30 km/h (19 mi/h)

3rd

→

4th: 40 km/h (25 mi/h)

4th

→

5th: 50 km/h (31 mi/h)

5th

→

6th: 60 km/h (37 mi/h)

Shift down points:

6th

→

5th: 25 km/h (16 mi/h)

5th

→

4th: 25 km/h (16 mi/h)

4th

→

3rd: 25 km/h (16 mi/h)

3rd

→

2nd: 25 km/h (16 mi/h)

2nd

→

1st: 25 km/h (16 mi/h)

U39P10E0.book Page 3 Thursday, October 7, 2010 5:12 PM

«
...
40
41
42
43
44
...
»

Summary of Contents for FZ8













































































































Reviews:

No comments

Related manuals for FZ8

VIKING 3250D FGS

Brand: Lincoln Electric Pages: 56

990D0-31J50-CLE

Brand: Suzuki Pages: 12

Brand: Free Spirits Pages: 28

Brand: DYNATEK Pages: 4

Brand: Chicago Electric Pages: 7

Brand: Chicago Electric Pages: 10

Brand: JAWA Pages: 40

Brand: Yamaha Pages: 96

R15 YZF155 2018

Brand: Yamaha Pages: 94

Brand: Yamaha Pages: 108

Brand: Yamaha Pages: 112

Road Star XV16ALER

Brand: Yamaha Pages: 126

Brand: Yamaha Pages: 299

Brand: Denali Pages: 3

Brand: MT Helmets Pages: 28

TORNADO Tre Novecento 900

Brand: Benelli Pages: 48

Brand: Benelli Pages: 108

MANA 850 GT ABS

Brand: APRILIA Pages: 197

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands