Yamaha FZ8 Owner'S Manual Download

Page: 55 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-12

TIP

An oil filter wrench is available at a
Yamaha dealer.

6. Apply a thin coat of clean engine

oil to the O-ring of the new oil filter
cartridge.

TIP

Make sure that the O-ring is properly
seated.

7. Install the new oil filter cartridge

with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.

8. Install the engine oil drain bolt and

its new gasket, and then tighten
the bolt to the specified torque.

9. Refill with the specified amount of

the recommended engine oil, and
then install and tighten the oil filler
cap.

1. Oil filter wrench
2. Oil filter cartridge

1. O-ring

1. Torque wrench

Tightening torque:

Oil filter cartridge:

17 Nm (1.7 m·kgf, 12 ft·lbf)

Tightening torque:

Engine oil drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lbf)

U39P10E0.book Page 12 Thursday, October 7, 2010 5:12 PM

Summary of Contents for FZ8













































































































Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands

Yamaha FZ8, Owner'S Manual

Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands