Yamaha FZ8 Owner'S Manual Download

Page: 81 / 108

PERIODIC MAINTENANCE AND ADJUSTMENT

7-38

EAU24360

Front wheel

EAU49831

To remove the front wheel

WARNING

EWA10821

To avoid injury, securely support the
vehicle so there is no danger of it
falling over.

1. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

2. Lift the front wheel off the ground

according to the procedure in the
previous section “Supporting the
motorcycle”.

3. Remove the brake hose holder on

each side by removing the bolt and
nut.

4. Remove the brake caliper (togeth-

er with the reflector) on each side
by removing the bolts.

NOTICE:

Do not apply the brake after the
brake calipers have been re-
moved, otherwise the brake
pads will be forced shut.

[ECA11051]

5. Pull the wheel axle out, and then

remove the wheel.

EAU49841

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground, and then put the
sidestand down.

4. Install the brake calipers (together

with the reflectors) by installing the
bolts.

1. Front wheel axle pinch bolt

2. Wheel axle
3. Brake caliper bolt

2
1

1. Brake hose holder
2. Bolt and nut

1. Brake caliper bolt
2. Brake caliper

3. Reflector

U39P10E0.book Page 38 Thursday, October 7, 2010 5:12 PM

Summary of Contents for FZ8













































































































Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands

Yamaha FZ8, Owner'S Manual

Search results

Summary of Contents for FZ8

Reviews:

Related manuals for FZ8

Brands by name

Popular brands