background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-29

7

EAU23202

Checking and lubricating the 
sidestand 

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10731

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it. Otherwise,
the sidestand could contact the
ground and distract the operator, re-
sulting in a possible loss of control.

EAU23272

Checking the front fork 

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.

To check the condition

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur-

face and hold it in an upright posi-
tion. 

WARNING! To avoid injury,

securely support the vehicle so
there is no danger of it falling
over.

 [EWA10751]

2. While applying the front brake,

push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

NOTICE

ECA10590

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.

Recommended lubricant:

Lithium-soap-based grease

U39P10E0.book  Page 29  Thursday, October 7, 2010  5:12 PM

Summary of Contents for FZ8













































































































Reviews: