Yamaha FZ1-SW Owner'S Manual Download

Page: 91 / 98

SPECIFICATIONS

8-2

Gear ratio:

1st:

38/15 (2.533)

2nd:

33/16 (2.063)

3rd:

37/21 (1.762)

4th:

35/23 (1.522)

5th:

27/20 (1.350)

6th:

29/24 (1.208)

Chassis:

Frame type:

Diamond

Caster angle:

25.00 °

Trail:

109.0 mm (4.29 in)

Front tire:

Type:

Tubeless

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

MICHELIN/Pilot Road S

Manufacturer/model:

DUNLOP/D221FA

Rear tire:

Type:

Tubeless

Size:

190/50 ZR17M/C (73W)

Manufacturer/model:

MICHELIN/Pilot Road D

Manufacturer/model:

DUNLOP/D221G

Loading:

Maximum load:

190 kg (419 lb)
(Total weight of rider, passenger, cargo and
accessories)

Tire air pressure (measured on cold
tires):

Loading condition:

0–90 kg (0–198 lb)
Front:

250 kPa (36 psi) (2.50 kgf/cm²)

Rear:

290 kPa (42 psi) (2.90 kgf/cm²)

Loading condition:

90–190 kg (198–419 lb)
Front:

250 kPa (36 psi) (2.50 kgf/cm²)

Rear:

290 kPa (42 psi) (2.90 kgf/cm²)

High-speed riding:

Front:

250 kPa (36 psi) (2.50 kgf/cm²)

Rear:

290 kPa (42 psi) (2.90 kgf/cm²)

Front wheel:

Wheel type:

Cast wheel

Rim size:

17M/C x MT3.50

Rear wheel:

Wheel type:

Cast wheel

Rim size:

17M/C x MT6.00

Front brake:

Type:

Dual disc brake

Operation:

Right hand operation

Recommended fluid:

DOT 4

Rear brake:

Type:

Single disc brake

Operation:

Right foot operation

Recommended fluid:

DOT 4

Front suspension:

Type:

Telescopic fork

Spring/shock absorber type:

Coil spring/oil damper

Wheel travel:

130.0 mm (5.12 in)

Rear suspension:

Type:

Swingarm (link suspension)

Spring/shock absorber type:

Coil spring/gas-oil damper

Wheel travel:

130.0 mm (5.12 in)

U3C321E0.book Page 2 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

Summary of Contents for FZ1-SW



































































































Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands

Yamaha FZ1-SW, Owner'S Manual

Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands