Yamaha FZ1-SW Owner'S Manual Download | Manualshive

Page: 78 / 98

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

WARNING

EWA10790

Headlight bulbs get very hot. There-
fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

3. Place a new headlight bulb into po-

sition, and then secure it with the
bulb holder.

CAUTION:

ECA10650

Take care not to damage the follow-
ing parts:

●

Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

●

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.

4. Install the headlight bulb cover,

and then connect the coupler.

5. Have a Yamaha dealer adjust the

headlight beam if necessary.

1. Headlight bulb holder

1. Do not touch the glass part of the bulb.

U3C321E0.book Page 31 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

«
...
76
77
78
79
80
...
»

Summary of Contents for FZ1-SW



































































































Reviews:

No comments

Related manuals for FZ1-SW

SIDE FORCE 445cc

Brand: Mash Pages: 27

Brand: SCORPION Pages: 12

Brand: hepco & becker Pages: 4

Brand: Honda Pages: 140

Brand: hepco & becker Pages: 5

Brand: TVS Pages: 60

Brand: Baja motorsports Pages: 66

Brand: Yamaha Pages: 86

Brand: Yamaha Pages: 88

TDM850'99 4TX-AE3

Brand: Yamaha Pages: 43

Brand: Yamaha Pages: 118

Brand: Yamaha Pages: 92

Brand: Yamaha Pages: 105

Brand: Yamaha Pages: 111

Brand: Yamaha Pages: 88

Brand: Yamaha Pages: 94

STRATOLINER XV19CTSC

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands