Yamaha FZ1-SW Owner'S Manual Download

Page: 81 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

EAU24360

Front wheel

EAU40060

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Place the vehicle on the center-

stand.

2. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

3. Remove the brake hose holder on

each side by removing the bolt and
nut.

4. Remove the brake caliper on each

side by removing the bolts.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

5. Pull the wheel axle out, and then

remove the wheel.

EAU40070

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Install the brake caliper on each

side by installing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

4. Install the brake hose holder on

each side by installing the bolt and
nut.

5. Take the vehicle off the center-

stand so that the front wheel is on
the ground.

6. Tighten the wheel axle, the front

wheel axle pinch bolt, and the
brake caliper bolts to the specified
torques.

1. Front wheel axle pinch bolt

2. Wheel axle

1. Brake hose holder
2. Bolt and nut

3. Brake caliper bolt

4. Brake caliper

U3C321E0.book Page 34 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

Summary of Contents for FZ1-SW



































































































Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands

Yamaha FZ1-SW, Owner'S Manual

Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands