Yamaha FZ1-SW Owner'S Manual Download

Page: 43 / 98

PRE-OPERATION CHECKS

4-3

Throttle grip

• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

6-15, 6-24

Control cables

• Make sure that operation is smooth.
• Lubricate if necessary.

6-23

Drive chain

• Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary.

6-21, 6-23

Wheels and tires

• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.

6-16, 6-18

Brake and shift pedals

• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.

6-24

Brake and clutch levers

• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.

6-25

Centerstand, sidestand

• Make sure that operation is smooth.
• Lubricate pivots if necessary.

6-25

Chassis fasteners

• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.

—

Instruments, lights, signals
and switches

• Check operation.
• Correct if necessary.

—

Sidestand switch

• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.

3-22

ITEM

CHECKS

PAGE

U3C321E0.book Page 3 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

Summary of Contents for FZ1-SW



































































































Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands

Yamaha FZ1-SW, Owner'S Manual

Search results

Summary of Contents for FZ1-SW

Reviews:

Related manuals for FZ1-SW

Brands by name

Popular brands