Yamaha FZ1-SW Owner'S Manual Download | Manualshive

Page: 30 / 98

background image

INSTRUMENT AND CONTROL FUNCTIONS

3-14

EAU26822

Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.

The brake lever is equipped with a po-
sition adjusting dial. To adjust the dis-
tance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “

” mark on the

brake lever.

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13072

Fuel tank cap

To open the fuel tank cap

Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

To close the fuel tank cap

1. Push the fuel tank cap into position

with the key inserted in the lock.

2. Turn the key counterclockwise to

the original position, remove it, and
then close the lock cover.

1. Brake lever

2. Brake lever position adjusting dial

3. “

” mark

4. Distance between brake lever and handlebar

grip

1. Brake pedal

1. Fuel tank cap lock cover

2. Unlock.

U3C321E0.book Page 14 Friday, September 29, 2006 4:57 PM

ProCarManuals.com

«
...
28
29
30
31
32
...
»

Summary of Contents for FZ1-SW



































































































Reviews:

No comments

Related manuals for FZ1-SW

Brand: Dayi Motor Pages: 15

Brand: hepco & becker Pages: 6

Brand: GAS GAS Pages: 57

Brand: Honda Pages: 178

Brand: R&G Pages: 13

ST400 Cruiser Edition

Brand: STEEL HORSE AUDIO Pages: 6

990D0-28K50-CLE

Brand: Suzuki Pages: 12

Light Bee QL3000DY

Brand: Surron Pages: 18

Brand: hepco & becker Pages: 6

Brand: Yamaha Pages: 80

Brand: Yamaha Pages: 144

Brand: Yamaha Pages: 84

Brand: Yamaha Pages: 255

Brand: Yamaha Pages: 17

Brand: Yamaha Pages: 120

Brand: Hudora Pages: 8

Brand: TM Pages: 80

Brand: SUR-RON Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands