Yamaha FZ1-NW Owner'S Manual Download Page 82

Page: 82 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-36

2. Lift the rear wheel off the ground

according to the procedure on
page 6-33.

3. Remove the axle nut.
4. Loosen the locknut on each side of

the swingarm.

5. Turn the drive chain slack adjust-

ing bolts fully in direction (a) and
push the wheel forward.

6. Remove the drive chain from the

rear sprocket.

NOTE:

●

If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.

●

The drive chain cannot be disas-
sembled.

7. While supporting the brake caliper

bracket, pull the wheel axle out,
and then remove the wheel.

CAUTION:

ECA11070

Do not apply the brake after the
wheel has been removed together
with the brake disc, otherwise the
brake pads will be forced shut.

EAU39411

To install the rear wheel

1. Install the wheel and the brake cal-

iper bracket by inserting the wheel
axle from the left-hand side.

NOTE:

●

Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.

●

Make sure that there is enough
space between the brake pads be-
fore installing the wheel.

2. Install the drive chain onto the rear

sprocket.

3. Install the axle nut, and then lower

the rear wheel so that it is on the
ground.

4. Adjust the drive chain slack. (See

page 6-21.)

5. Tighten the axle nut to the speci-

fied torque.

1. Wheel axle

1. Slot
2. Retainer

Tightening torque:

Axle nut:

150 Nm (15.0 m·kgf, 110 ft·lbf)

U2D121E0.book Page 36 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

Summary of Contents for FZ1-NW



































































































Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands

Yamaha FZ1-NW, Owner'S Manual

Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands