Yamaha FZ1-NW Page 63 Owner'S Manual Download | Manualshive

Page: 63 / 98

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-17

6

●

After extensive tests, only the
tires listed below have been ap-
proved for this model by
Yamaha Motor Co., Ltd.

●

Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.

●

Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.

WARNING

EWA10600

This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.

●

Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.

●

Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.

●

The tires must be warmed up
before a high-speed run.

●

Always adjust the tire air pres-
sure according to the operating
conditions.

EAU21960

Cast wheels

To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

●

The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.

●

The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.

●

Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.

Front tire:

Size:

120/70 ZR17M/C (58W)

Manufacturer/model:

MICHELIN/Pilot Road S
DUNLOP/D221FA

Rear tire:

Size:

190/50 ZR17M/C (73W)

Manufacturer/model:

MICHELIN/Pilot Road D
DUNLOP/D221G

FRONT and REAR:

Tire air valve:

TR412

Valve core:

#9100 (original)

U2D121E0.book Page 17 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

«
...
61
62
63
64
65
...
»

Summary of Contents for FZ1-NW



































































































Reviews:

No comments

Related manuals for FZ1-NW

Brand: R&G Pages: 21

Brand: R&G Pages: 2

Brand: R&G Pages: 8

Brand: Miller Pages: 22

Brand: hepco & becker Pages: 2

Brand: Engelbert Strauss Pages: 32

Brand: Datatool Pages: 5

Brand: DAINESE Pages: 59

Brand: Gemini Pages: 9

Brand: MT Helmets Pages: 28

Brand: Honda Pages: 114

Brand: R&G Pages: 9

Brand: KTM Pages: 122

Brand: B-PWR Pages: 11

Brand: Troy Lee Designs Pages: 63

Brand: Tao Motor Pages: 21

Express Saddlebags

Brand: Saddlemen Pages: 2

Brand: WangYe Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands