Yamaha FZ1-NW Page 80 Owner'S Manual Download

Page: 80 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-34

a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.

EAU24360

Front wheel

EAU39391

To remove the front wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the front wheel axle pinch

bolt, then the wheel axle and the
brake caliper bolts.

2. Lift the front wheel off the ground

according to the procedure on
page 6-33.

3. Remove the brake hose holder on

each side by removing the bolt and
nut.

4. Remove the brake caliper on each

side by removing the bolts.

CAUTION:

ECA11050

Do not apply the brake after the
brake calipers have been removed,
otherwise the brake pads will be
forced shut.

1. Front wheel axle pinch bolt

2. Wheel axle

1. Brake hose holder
2. Bolt and nut

3. Brake caliper bolt

4. Brake caliper

U2D121E0.book Page 34 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

Summary of Contents for FZ1-NW



































































































Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands

Yamaha FZ1-NW, Owner'S Manual

Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands