Yamaha FZ1-NW Page 81 Owner'S Manual Download

Page: 81 / 98

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

5. Pull the wheel axle out, and then

remove the wheel.

EAU39400

To install the front wheel

1. Lift the wheel up between the fork

legs.

2. Insert the wheel axle.
3. Lower the front wheel so that it is

on the ground.

4. Install the brake calipers by install-

ing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.

5. Install the brake hose holders by

installing the bolt and nut.

6. Tighten the wheel axle, the wheel

axle pinch bolt and the brake cali-
per bolts to the specified torques.

7. Push down hard on the handlebar

several times to check for proper
fork operation.

EAU25080

Rear wheel

EAU25311

To remove the rear wheel

WARNING

EWA10820

●

It is advisable to have a Yamaha
dealer service the wheel.

●

Securely support the motor-
cycle so that there is no danger
of it falling over.

1. Loosen the axle nut.

Tightening torques:

Wheel axle:

72 Nm (7.2 m·kgf, 52 ft·lbf)

Front wheel axle pinch bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lbf)

1. Axle nut

2. Locknut

3. Drive chain slack adjusting bolt
4. Brake caliper

5. Brake caliper bracket

U2D121E0.book Page 35 Tuesday, September 19, 2006 1:30 PM

ProCarManuals.com

Summary of Contents for FZ1-NW



































































































Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands

Yamaha FZ1-NW, Owner'S Manual

Search results

Summary of Contents for FZ1-NW

Reviews:

Related manuals for FZ1-NW

Brands by name

Popular brands