background image

INSTRUMENT AND CONTROL FUNCTIONS

3-10

3

If any of the immobilizer system circuits
are defective, the immobilizer system
indicator light will flash, and then the
display will indicate a two-digit error
code.

NOTE:

If the display indicates error code 52,
this could be caused by transponder in-
terference. If this error code appears,
try the following.

1. Use the code re-registering key to

start the engine.

NOTE:

Make sure there are no other immobi-
lizer keys close to the main switch, and
do not keep more than one immobilizer
key on the same key ring! Immobilizer
system keys may cause signal interfer-
ence, which may prevent the engine
from starting.

2. If the engine starts, turn it off and

try starting the engine with the
standard keys.

3. If one or both of the standard keys

do not start the engine, take the
vehicle, the code re-registering

key and both standard keys to a
Yamaha dealer and have the stan-
dard keys re-registered.

If the display indicates any error codes,
note the code number, and then have a
Yamaha dealer check the vehicle.

CAUTION:

ECA11590

If the display indicates an error
code, the vehicle should be checked
as soon as possible in order to avoid
engine damage.

LCD and tachometer brightness
control mode

This function allows you to adjust the
brightness of the LCD and the tachom-
eter panel and needle to suit the out-
side lighting conditions.

To set the brightness

1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but-

ton.

3. Turn the key to “ON”, and then re-

lease the “SELECT” button after
five seconds.

4. Push the “RESET” button to select

the desired brightness level.

5. Push the “SELECT” button to con-

firm the selected brightness level.
The display will return to the odom-
eter or tripmeter mode.

1. Tachometer panel
2. Tachometer needle

3. LCD

4. Brightness level

U2D121E0.book  Page 10  Tuesday, September 19, 2006  1:30 PM

ProCarManuals.com

Summary of Contents for FZ1-NW



































































































Reviews: