Yamaha F90 Owner'S Manual Download

Page: 62 / 112

Operation

While pressing and holding the pressure
relief tab under the fuel tank cap, slowly
turn the fuel tank cap counterclockwise
1/4 turn.

TIP:

Release the fuel vapor contained in the fuel
tank.
6.

While pressing and holding the pressure
relief tab under the fuel tank cap again,
turn the fuel tank cap counterclockwise
to remove it.

Fill the fuel tank with fuel.

WARNING! Do

not overfill. Otherwise fuel can expand
and overflow if the temperature in-
creases.

[EWM02611]

TIP:

Wipe up any spilled gasoline immediately
with dry rags.

Dispose of rags properly according to local
laws or regulations.

Turn the fuel tank cap clockwise to tight-
en until a click is heard.

1. Air vent screw

1. Pressure relief tab
2. Fuel tank cap

ZMU07445

ZMU07446

1. Pressure relief tab
2. Fuel tank cap

Fuel tank capacity:

25 L (6.61 US gal, 5.50 Imp.gal)

ZMU07447

ZMU07448

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F90

















































































































Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands

Yamaha F90, Owner'S Manual

Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands