Texas Instruments bq24187 Скачать руководство пользователя

Страница: 1 / 21

User's Guide

SLUUAI5 – April 2014

bq24187 Evaluation Module User's Guide

The bq24187 evaluation module is a complete charger module for evaluating compact, flexible, high-
efficiency, USB-friendly, switch-mode charge management solution for single-cell, Li-ion and Li-polymer
batteries used in a wide range of portable applications.

Contents

Introduction

...................................................................................................................

1.1

BQ24187 IC Features

..............................................................................................

1.2

bq24187EVM Features

............................................................................................

1.3

Schematic

............................................................................................................

1.4

I/O Description

......................................................................................................

1.5

Test Points to IC Pins

..............................................................................................

1.6

Control and Key Parameters Setting

.............................................................................

1.7

Recommended Operating Conditions

............................................................................

Test Summary

................................................................................................................

2.1

Definitions

............................................................................................................

2.2

Recommended Test Equipment

..................................................................................

2.3

Recommended Test Equipment Setup

..........................................................................

2.4

Recommended Test Procedure

...................................................................................

Printed-Circuit Board Layout Guideline

..................................................................................

Bill of Materials and Board Layout

......................................................................................

4.1

Bill of Materials

....................................................................................................

4.2

Board Layout

.......................................................................................................

List of Figures

bq2418xEVM Schematic

....................................................................................................

BAT_Load (PR1010) Schematic

...........................................................................................

Connections of HPA172 Kit

................................................................................................

Recommended Initial Test Setup for bq24187EVM-625

...............................................................

Main Window of BQ24187SW Evaluation Software

.....................................................................

Top Assembly Layer

.......................................................................................................

Top Layer

...................................................................................................................

First Internal Layer

.........................................................................................................

Second Internal Layer

.....................................................................................................

Bottom Layer

................................................................................................................

List of Tables

Bill of Materials - PWR625A

.............................................................................................

SLUUAI5 – April 2014

bq24187 Evaluation Module User's Guide

Submit Documentation Feedback

Содержание bq24187






















Результаты поиска

Содержание bq24187

Отзывы:

Похожие инструкции для bq24187

Бренды по названию

Популярные бренды

Texas Instruments bq24187, Руководство пользователя

Результаты поиска

Содержание bq24187

Отзывы:

Похожие инструкции для bq24187

Бренды по названию

Популярные бренды