Yamaha F90 Page 59 Owner'S Manual Download

Page: 59 / 112

Operation

Check that the oil level on the oil dipstick
is between the upper and lower marks.
Consult your Yamaha dealer if the oil lev-
el is not at the proper level or if it appears
milky or dirty.

EMU40412

Outboard motor

Check that the outboard motor is mounted
properly and check the outboard motor
mounting bolts for looseness.

Check the propeller for damage.

Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose
connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out and
the engine can overheat during operation.

[ECM01802]

EMU36965

Install cowling

Be sure that all cowling lock levers are
released.

Be sure that the rubber seal is seated all
the way around the top cowling.

Place the top cowling on the bottom
cowling.

Check to be sure the rubber seal is seat-
ed correctly between the top cowling
and the bottom cowling.

Move the cowling lock levers to lock the
top cowling as shown.

NOTICE:

If the

top cowling is not installed correctly,

1. Oil dipstick
2. Upper mark
3. Lower mark

ZMU08224

1. Fitting
2. Garden hose connector
3. Flushing device

1. Top cowling
2. Rubber seal

ZMU08089

ZMU08090

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F90

















































































































Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands

Yamaha F90, Owner'S Manual

Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands