Yamaha F90 Page 103 Owner'S Manual Download

Page: 103 / 112

Trouble Recovery

There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.

This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.

The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

If the water separator-alert indicator blinks or
the buzzer sounds intermittently, perform the
following procedure.

TIP:

The buzzer sounds only when the remote
control lever is placed in neutral.

Stop the engine.

Remove the top cowling.

Remove the water detection switch lead
from the holder.

Disconnect the water detection switch
coupler.

NOTICE:

Be careful not to get

any water on the water detection
switch coupler, otherwise a malfunc-
tion could occur.

[ECM01951]

1. Water separator-alert indicator

ZMU05441

ZMU01758

1. Holder
2. Water detection switch coupler

ZMU07012

ZMU08704

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F90

















































































































Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands

Yamaha F90, Owner'S Manual

Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands