Yamaha F90 Owner'S Manual Download Page 6 | Manualshive

Page: 6 / 112

Yamaha F90 Owner'S Manual Download Page 6

Table of contents

Trimming outboard motor ............. 65

Adjusting trim angle (Power trim

and tilt) .......................................... 66

Adjusting boat trim ........................... 66

Tilting up and down ...................... 67

Procedure for tilting up (power trim

and tilt models) ............................. 68

Procedure for tilting down................ 69

Shallow water ............................... 70

Cruising in shallow water ................. 70

Cruising in other conditions .......... 71

Maintenance .................................... 72

Transporting and storing outboard

motor.......................................... 72

Storing outboard motor.................... 72
Conditioning and stabilizing

gasoline......................................... 73

Procedure......................................... 73
Lubrication ....................................... 74
Cleaning and anticorrosion

measures ...................................... 74

Flushing cooling water passage....... 75
Cleaning the outboard motor ........... 75
Checking painted surface of

outboard motor............................. 76

Periodic maintenance ................... 76

Replacement parts ...........................  76
Maintenance interval guidelines.......  76
Maintenance chart 1 ........................  77
Maintenance chart 2 ........................  80
Greasing ...........................................  81
Inspecting spark plug.......................  82
Inspecting idle speed .......................  83
Changing engine oil..........................  83
Inspecting wiring and connectors ....  85
Checking propeller ...........................  86
Removing propeller ..........................  86
Installing propeller ............................  87
Changing gear oil .............................  88
Inspecting and replacing anode(s) ...  89
Checking battery (for electric start

models) ......................................... 89

Connecting the battery..................... 90

Disconnecting the battery ................ 91

Trouble Recovery............................ 92

Troubleshooting............................ 92
Temporary action in emergency ... 95

Impact damage ................................ 95
Replacing fuse.................................. 95
Power trim and tilt unit will not

operate.......................................... 96

Water separator-alert is activated

after leaving port ........................... 96

Treatment of submerged motor.... 98

Consumer information (For North
America)........................................... 99

YAMAHA FOUR-STROKE

OUTBOARD MOTOR
THREE-YEAR LIMITED
WARRANTY ............................... 99

IMPORTANT WARRANTY

INFORMATION IF YOU USE
YOUR YAMAHA OUTSIDE THE
U.S.A. OR CANADA................. 101

INDEX ............................................. 102

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
4
5
6
7
8
...
»

Summary of Contents for F90

















































































































Reviews:

No comments