Yamaha F90 Page 101 Owner'S Manual Download

Page: 101 / 112

Trouble Recovery

A. Have serviced by a Yamaha dealer.

Q. Is fuel joint connection incorrect?
A. Connect correctly.

Q. Is heat range of spark plug incorrect?
A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29434

Temporary action in emergen-

EMU29442

Impact damage

WARNING

EWM00871

The outboard motor can be seriously
damaged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

Stop the engine immediately.

Check the control system and all compo-
nents for damage. Also, check the boat
for damage.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

Have a Yamaha dealer check the out-
board motor before operating it again.

EMU46602

Replacing fuse

WARNING

EWM00632

Substituting an incorrect fuse or a piece of
wire could allow excessive current flow.
This could cause electric system damage
and a fire hazard.

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F90

















































































































Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands

Yamaha F90, Owner'S Manual

Search results

Summary of Contents for F90

Reviews:

Related manuals for F90

Brands by name

Popular brands