Yamaha F300 Page 110 Owner'S Manual Download | Manualshive

Page: 110 / 124

background image

104

Trouble Recovery

EMU29427

Troubleshooting

A problem in the fuel, compression, or igni-
tion systems can cause poor starting, loss of
power, or other problems. This section de-
scribes basic checks and possible remedies,
and covers all Yamaha outboard motors.
Therefore some items may not apply to your
model.
If your outboard motor requires repair, bring
it to your Yamaha dealer.
If the engine trouble-alert indicator is flash-
ing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of
recommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?

A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 61.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten
all loose connections. Replace worn or bro-
ken wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine shut-off cord (lanyard) not at-
tached?
A. Attach cord.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
108
109
110
111
112
...
»

Summary of Contents for F300





























































































































Reviews:

No comments

Related manuals for F300

RouterBOARD 411

Brand: 4gon Pages: 2

Brand: SurfLink Pages: 9

Brand: MATSONIC Pages: 78

Brand: Biostar Pages: 166

EVAL-IH-R5IPB-A-V1

Brand: Infineon Pages: 34

Brand: MSI Pages: 106

Thunder HEsl S2567

Brand: TYAN Pages: 60

Brand: ASROCK Pages: 92

Brand: Silicon Laboratories Pages: 13

STEVAL-IHM011V1

Brand: ST Pages: 27

Brand: Linear Technology Pages: 10

Brand: CDI Pages: 4

Brand: Abit Pages: 134

SY-P4-645DX DRAGON Ultra

Brand: SOYO Pages: 173

Brand: Acorp Pages: 68

Brand: Acorp Pages: 74

Brand: Suzuki Pages: 50

Brand: Gan Systems Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands