Yamaha F300 Page 58 Owner'S Manual Download | Manualshive

Page: 58 / 124

background image

52

Installation

EMU26902

Installation

The information presented in this section is
intended as reference only. It is not possible
to provide complete instructions for every
possible boat and motor combination. Prop-
er mounting depends in part on experience
and the specific boat and motor combination.

WARNING

EWM01590

●

Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower
than the maximum rating on the capac-
ity plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.

●

Improper mounting of the outboard mo-
tor could result in hazardous condi-
tions such as poor handling, loss of
control, or fire hazards. For permanent-
ly mounted models, your dealer or oth-
er person experienced in proper

rigging should mount the motor.

EMU35811

Mounting the outboard motor

The outboard motor should be mounted so
that the boat is well balanced. Otherwise, the
boat could be hard to steer. For single-en-
gine boats, mount the outboard motor on the
centerline (keel line) of the boat.
For twin engine boats, mount the outboard
motors equidistant from the centerline.
For triple engine boats, mount the center out-
board motor on the centerline (keel line), and
the port side and starboard side outboard
motors equidistant from the center outboard
motor.
Consult your Yamaha dealer or boat manu-
facturer for further information on determin-
ing the proper mounting location.

EMU26931

Mounting height (boat bottom)

The mounting height of your outboard motor
affects its efficiency and reliability. If it is
mounted too high, propeller ventilation may

1. Center line (keel line)

1. Center line (keel line)

1. Center line (keel line)

ZMU01760

1

ZMU05957

1

©

2019 Yamaha Motor Corporation, U.S.A.

«
...
56
57
58
59
60
...
»

Summary of Contents for F300





























































































































Reviews:

No comments

Related manuals for F300

Brand: Balluff Pages: 62

Brand: Yamaha Pages: 76

Brand: Aaeon Pages: 40

Brand: Gigabyte Pages: 116

Brand: Texas Instruments Pages: 25

Brand: Mercury Pages: 102

Brand: MSI Pages: 171

Brand: Javad Pages: 12

Brand: Texas Instruments Pages: 24

Brand: u-blox Pages: 24

Brand: Portwell Pages: 9

Brand: TYAN Pages: 74

LanParty 925X-T2

Brand: DFI Pages: 129

Brand: DG Pages: 18

AIROC IFW956810

Brand: Infineon Pages: 4

SPC58XXADPT144S REV.B

Brand: ST Pages: 19

Brand: ASROCK Pages: 139

Brand: ASROCK Pages: 163

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands