Yamaha F300 Page 117 Owner'S Manual Download

Page: 117 / 124

Trouble Recovery

111

11. Connect the water detection switch cou-

pler securely until a click is heard.

12. Securely attach the water detection

switch coupler to the holder.

13. Connect the lead to the holder.

14. Install the top cowling.
15. Start the engine and make sure that the

water separator-alert indicator remains
off. Have a Yamaha dealer inspect the
outboard motor after returning to port.

EMU33501

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.

NOTICE:

Do not attempt to run the

outboard motor until it has been com-
pletely inspected.

[ECM00401]

Bolt tightening torque:

8.0 Nm (0.8 kgf-m, 5.8 ft-lb)

1. Water detection switch coupler

ZMU05895

ZMU05897

ZMU05898

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for F300





























































































































Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands

Yamaha F300, Owner'S Manual

Search results

Summary of Contents for F300

Reviews:

Related manuals for F300

Brands by name

Popular brands